Відео

We usually have lovely skys and weather in the Caribbean, im not very far from there

Thats water being wasted. Steam is invisible.

Use a will bladder tank where you can pressurize the bladder overtime with the fuel and it would give you better pressure and cost-effective

In my opinion compresor should be closer to injection, it makes the geometry more stable Btw, Nice work

may be up size the jet if you ant all ready on the engine on compressor richen it up a bit the next size drill bit up the main jet via a hand mini drill bit i did that to my pressure washer and racing mud mower mud mower runs a bit fat fuel but no longer dies taking off due to up gearing and lack of traffic pump [squirter jet] all so on intake port add a ruff texture to the runner floor help atomize the fuel can do that with a burr going along the short turn of heads intake port .it will help possible fix the issue

Considering myself in the group of "men" I've fully enjoyed the video. 😅🔥

did u mean to say contrails or chemtrails 0:40

You know i always have an eye on you! Regards!

Why use oxygen if enough fresh air is available?

probably should have made it like a jet engine with can or flame holder on the inside

Ford is crap , so if your fender liner wasn't ripped apart you would need to remove the tire and fender liner for access to the valve.

How can the water go through the flash boiler?, are u using water pump sir?

What voltage was going to the electrodes here?

Do us all a favor and take down this video please. If you don't know what your doing then why post a video of it? It's clear that you have no idea how the torch works or why hole is there yet you decide to plug it up? Video like this cause injuries.

Lol. That's called, by a new deck!

Wiretek 1001 seems good but It's tough picking the right spot

Yes lawnmowers can be a real waste of time to fix. When I work on them I make sure it's a good repeat customer that doesn't mind spending money. Or it's an expensive mower that's worth sinking time into. And on stuff like that bill by the hr. There are many times I wouldn't want to hire myself

What thickness copper tube did you use? L or M?

Bro you should not be doing this. You have a leak by the way. Check your evap coil for a leak. And you dont go off psi you go off superheat subcool.

You have a leak if you have to recharge. Most likely it's the valve cores on those service ports. Put some 1/4 inch brass flare caps with copper gaskets on those ports to prevent leakage.

Wouldn't .68 caliber glass balls be extremely dangerous if they hit someone and shattered? Could the glass shards potentially cause eye injuries, blindness, or enter the lungs and cause internal damage like major cuts?

That's not a worn part, THIS is a worn part! 😅🐊

That's not a propane explosion. That is a high explosive. Nothing in an AC system can detonate like that except maybe C4. That outdoor unit must've had a bomb planted. Maybe if you charge the AC with propane and pure oxygen, maybe then it'll look like that. Without oxygen, nothing burns, nothing explodes.

tomorrow will be a better day

Wouldn't it be cheaper to replace the deck ?

Im having this issue as well but when i squeeze the trigger it seems that rhe freon isnt passing through, any clue why it would do that?

Most commonly a low charge is the cause of a frozen evap but there could be other issues. You can google a temperature pressure chart for the refrigerant you are using. I don’t do residential but I work on refrigeration. Always check airflow first. Nice clean coils. Then fan operation. Check for drain obstructions if all that is good and compressor is running then it’s on the refrigeration side. Put gauges on as a last resort. Also it’s good to see the high side as well. If you have a restriction, you could be overcharging by adding refrigerant. Gauges on the high press side would show you that. If you know u have a slow leaker then it’s probably fine topping it off like you did.

Anyone can tell me what to do if i checked the bulb but turns out to be a small LED light that sauderd

I think that they have a similar compressor priced at 2K in June 2024.

Hi Bob it's Dan from Israel im trying to reach you on phone or WhatsApp, no reply its shut down. How can i connect you please 🙏

I figured out these pumps at work. I have to clean them on a regular basis because of the torture the poor little pumps are subjected to.

And my dumb ass has been trying to light 100% oil for like 3 years now with almost zero luck. What a waste of time and materials, I wish I'd seen this YEARS ago. Smdh.

Hey man! I got a question. I need it to burn at 1500 Celsius at 9 feet. Is that possible? Thanks!

Helped a lot thanks buddy, ac is cold now

Thank you for making this video.

Some clown air gunned my wheel nuts on super tight, of course one broke upon trying to get off, couldn't get 19mm socket to take like you managed even tho bolt is that size , old Volvo doesn't want to play 😢

HONEYWELL EXPLOSIVE ORDNANCE DISPOSAL (EOD) SUIT FOR HVAC TECHNICIANS AND INSTALLERS. $1899.95

There's nothing to see here. Everything is normal. Nothing to worry about. It's safe. I heard the same thing in 2021 about a certain schott. Everything is normal. Nothing to see here. Move along please, move along.

(1) Please, what's the role of play sand in this refractory mix? I did not see you add it to the formula. (2) The Black Blasting media, what material is that or its composition?

Saving the planet isn't cheap or safe 😂

You just needed Platinum tips yo. An oil burner ignition transformer, little bit of platinum and you'll have that jar Brown AF in like 5 minutes flat

What size tubing did you use?

My 2005 Tahoe AC has worked flawlessly in the three years I have had it. I had a reputable oil service change done a week ago and they said the AC system needs work. I said my AC is ice cold. I used the AC three times since then and had cold AC. Now, the compressor clicks on and off. Do you think they did something to make it fail, to make work?

Bro. You are the most awesome at making ALL THESE BURNERS !!! I don’t know a single channel that would create at least half of the burners that you created ! Not even every company creates as many burners as you create !! This is a huge job. Great respect!!! Thanks to you, I realized that creating burners and melting metal is not so difficult !!!

do it agen 7 ad water then you will get hydrogen now ad water drip

I think your suppose to loop the exhaust of nitric oxide back into the chamber so the NO is continually converted to NO2

I feel like my compressor never fully kicks on, what do I do

If you want a torch, get the cutting tip for propane, don't waste your time and money with acetylene, unless you need to Carberize, like protecting chrome shafting for welding. Plus with propane you can crank input pressure right up.(over 15psi) Especially when heating metal..

yeah you can keep old cars running long with this kind of stuff.

Really appreciate this video sir it’s got my ac system working like it should in my 2009 ford crown vic 🍻